As an Amazon Associate I earn from qualifying purchases.1. Reland Sun
Reland Sun 1pcs L293D L293 Motor Driver Shield L293D motor control shield motor drive expansion board motor shield
Reland Sun - The h bridge is typically an electrical circuit that allows a voltage to be applied to an output in each direction, such as motor. Basically, this means that with this chip you can use DC motors and power supplies up to 12 volts.
L293d is a monolithic 4-channel high voltage high-current monolithic driver. Can drive 4 dc motors or 2 stepper motors or 2 servos. These are some pretty large motors and the chip can deliver a maximum current of 600mA per channel, the L293D chip is also what is known as a kind of H bridge.
2. Lysignal
Lysignal L293D Motor Control Shield Motor Drive Expansion Board for Arduinos MEGA/UNO Diecimila & Duemilanove Robot Car Motor Control Shield
Lysignal - L293d chip provides 06a peak 1. 2a current per way, and has thermal power off protection, can run motors on 4. 5v to 36V. Basically this means using this chip you can use DC motors and power supplies of up to 36 Volts.
Up to 4 bidirectional dc motors and 4 way pwm speed regulation about 05% resolution; up to two stepper motors are in forward and reverse control, single / double step control, staggered or microstepping and rotation angle control.
L293d chips are also known as type h bridges. The h-bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.
G. Monolithic integrated, high current, high voltage, 4-channel driver. Pull-down resistors keep motors disabled during power-up. 4 way h-bridge. Tested compatible for Mega, Diecimila & Duemilanove. Motor. With arduin reset button; 2 external terminal power interface, for separating logic/motor supplies.
Brand | Lysignal |
Manufacturer | LYCHEE LIMITED |
Height | 2 cm (0.79 Inches) |
Length | 6 cm (2.36 Inches) |
Weight | 0.01 kg (0.02 Pounds) |
Width | 5 cm (1.97 Inches) |
Part Number | Kawayy |
3. RETYLY
RETYLY DRV8825/A4988 42 Stepper Driver Module Motor Control Shield Drive Expansion Board for R3 3D Printer DIY Kit
RETYLY - Suitable for 42 stepper motor drive, 3D printers and DIY. Terminal power for easy connection of drive power. On-board dip switch, you can easily adjust the drive segments. Compatible with 12/24V drive scheme. Highly integrated expansion board, small size, stable performance.
4. Katigan
Katigan DRV8825/A4988 42 Stepper Driver Module Motor Control Shield Drive Expansion Board for R3 3D Printer DIY Kit
Katigan - Suitable for 42 stepper motor drive, 3D printers and DIY. Terminal power for easy connection of drive power. Highly integrated expansion board, small size, stable performance. On-board dip switch, you can easily adjust the drive segments. Compatible with 12/24V drive scheme.
5. BOBEINI
BOBEINI L293D Motor Control Shield Motor Drive Expansion Board for Duemilanove Module
BOBEINI - The l293d is a monolithic integrated, high voltage, high current, 4-channel driver. Can drive up to 2 stepper motors unipolar or bipolar with single coil, double coil or interleaved stepping. The board can be used to interface microcontrollers to DC motors and power supplies of up to 36 Volts.
2 interfaces for 5V for Servo connected to the high-resolution dedicated timer. Can drive 4 dc motors or 2 stepper motors or 2 servos. Can drive up to 4 bi-directional DC motors with individual 8-bit speed selection.
6. WENDI
@WENDi Motor Control Shield Drives 4 DC Motors or 2 Stepping Motors
WENDI - Esd protection. Configurable motor power supply via onboard jumper. Be capable of driving 4 DC motors or 2 stepping motors at one time.
With 2 l293d, each l293d can drive 2 DC motors or 1 stepping motor at one time. Totally 4 channel h-bridge, with 600mA output current peak 1. 2a per single bridge.
Brand | WENDI |
Manufacturer | WENDI |
Part Number | 1 |
Model | 722204928453 |
7. UIOTEC
UIOTEC Raspberry Pi 3 A + B + 2 generation B-type expansion board ARPI600 supports XBEE GSM/GPRS/Motor Control Shield
UIOTEC - Xbee-board interface for easy access to a variety of XBee modules. Onboard rtc, which is one of the most commonly used functions. Onboard sensor interface, easy access to a variety of sensors.
Onboard usb to uart, serial facilitate debugging, can also be configured as XBee USB Adapter. Onboard adc, 11 channels 6 channels for Ard uino interface, 10 bit, 38KSPS, 5 channel for accessing sensor.
8. Garciakia
TB6612FNG Dual DC Stepper Motor Control Drive Expansion Shield Board Module for Arduino Microcontroller Better than L298N
Garciakia - 4. 4. 5. 5. Widely used in experiment, industry, robot, electronic DIY etc. All pins of the tb6612fng broken out to 01" spaced pins, input pins are on one side and output pins are on the other.
Built-in thermal shutdown circuit and low voltage detecting circuit. 1. 1. Cw/ccw/short brake/stop motor control modes. Filtering capacitors on both supply lines. 3. 3. 2. 2.
9. YOUMILE
Youmile L298P Motor Driver Module High-power L298P PWM Speed Controller H-bridge Driver Shield Expansion Board DC Stepper Motor Controller Bluetooth Interface For Arduino
YOUMILE - Stack design can be directly plugged into the Arduino, easier to use. L298p chipadopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A.
High-speed schottky diodesUse eight high-speed Schottky diodes at motor output as protection. Performancethe l298p shield dc motor driver has PWM speed control mode; Dual high-power H-bridge driver. Inputdriven part of the input voltage vs: vin Input 6. 5 ~ 12v, pwrin 4. 8 ~ 35v input.
10. GGOOD
Stepper Motor Driver Board Motor Driver Control Module Extension Shield Board 5PCS Industrial Control
GGOOD - Motor power supply: stepper motor driver board needs a 7V to 30V power supply to power the motor, and the power supply provides power for any power supply to the motor.
Motor control: stepper motor Module connects a 4-wire stepper motor and a microcontroller to obtain precise motor control. Bipolar motor: stepper driver module is used to drive bipolar motors and motors, 4, connected as bipolar, that is, 6 or 8 wire stepper motors.
With regulator: motor driver module has an on-board voltage regulator for digital interface, which can be set to 5V or 3. 3v. Easy to use: motor driver control Board is a stepper motor driver that can be used directly, you can output digital to 5V arbitrarily.
Brand | GGOOD |
Manufacturer | GGOOD |
Height | 0.9 cm (0.35 Inches) |
Length | 4.85 cm (1.91 Inches) |
Weight | 0.04 kg (0.08 Pounds) |
Width | 2 cm (0.79 Inches) |
Part Number | D2GSHGLRMI211122 |